TeraFlex Jeep JL & Jeep JT 70 in. Tera60 HD Front w/ Locking Hub - No Ring & Pinion, Locker, Carrier (0-6 in. Lift) - 3170000

TeraFlex Jeep JL & Jeep JT 70in. Tera60 HD Front w/Locking Hub - No Ring & Pinion, Locker, Carrier (0-6in. Lift) - 3170000

The unloaded Tera60 HD Front Axle Assembly w/ Locking Hub includes SlimLock Hub Kit, Super 60 bearings, inner and outer axle shafts, knuckle assembly, ball joints, brakes, and sensors. Add your choice of ring and pinion gear ratio, locker, and carrier.

TeraFlex HD Front Axle Housings are perfect for replacing bent, broken, or damaged axles in JL Wrangler/Unlimited and JT Gladiator vehicles including Rubicon models. Can also be used as a direct bolt-on upgrade for Jeep owners looking to beef up the stock axles' weak areas.

Tera60 HD Front Axle Housings are the ultimate upgrade for JL and JT models requiring maximum suspension up travel and compression. Compatible with all Super 60 gear ratios for extreme duty applications requiring additional ring and pinion strength.

Our heavy-duty axle housings feature smooth profile surfaces, axle tubes, all necessary mount brackets, control arm bushings, forged inner knuckles, and more!

Features/Benefits::

• Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability


• 3.25 inch O.D. x 0.375 inch wall DOM axle tube for superior strength vs. weight


• 70 inch WMS-WMS and 8x6.5 inch wheel bolt pattern


• Fixed spindle mount hub assembly


• Tera60 specific high-pinion front axle housing design


• Includes 1350 series pinion yoke


• 35-spline inner axle shafts and outer stub shafts


• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing


• Oversized outer pinion bearing handles increased torque and high-load conditions


• High-capacity housing holds maximum amount of oil


• Asymmetric housing design for extra-long tube side strength


• Pre-installed inner axle seals


• HD forged inner knuckles w/ greater upper and lower section strength


• Ductile cast iron housing w/ increased rib gussets


• HD ductile iron differential cover


• Smooth radius bottom design to glide over rocks and obstacles


• Integrated lower control arm skid plates


• High-flow oil passages


• Bottom oil drain hole for simple fluid changes


• Reinforced front track bar mount (ties into spring pad) for greater strength


• UV protected triple-stage powder coat for corrosion resistance


• 1/4 inch-thick CNC laser cut axle brackets for extreme strength


• Integrating the front upper control arm mounts into the housing increases up travel an additional 2 inch compared to other aftermarket Dana 60 axles


• Pre-installed upper control arm bushings


• Proper pinion angle and raised track bar bracket for lifted JL/JT applications


• Pre-tapped hole on spring perch for bump stop extensions


• Pre-drilled holes for limit straps and lower spring retainers


• Retains all JL/JT ESP, ABS, and speedometer sensor capability


• 100 percent engineered, designed, and built in the USA w/ new components


• 1-Year/Unlimited Mileage Warranty

Includes:

• Spicer bearings and install kits


• 35-spline inner axle shafts


• 35-spline outer stub shafts


• Spicer HD Ball Joints


• 1350 series pinion yoke


• Dana 60: SlimLock Hub Kit (Part Number 3449350)


• Delta Brake Kit - Front (Part Number 4403481)


• HD Chromoly Tie Rod Kit (Part Number 1863910)


• HD Differential Cover Kit

Fits:

• JL Wrangler (2-door)


• JL Wrangler Unlimited (4-door)


• JT Gladiator (pickup)


• 0-6 inch Lift

Specs:

• WMS-WMS: 70 inch


• Axle Tube: 3.25 inch x 0.375 inch


• Wheel Bolt Pattern: 8x6.5 inch

Product Notes:

• Optimize your setup by upgrading your steering system with our heavy-duty steering components. The factory steering system may also be reused.


• HD Forged Drag Link Kit (0-6 inch Lift) (Part Number 1863920)


• Requires adjustable control arms for caster angle adjustments